Search Results for: e4200

Kernel Version vs Firmware Version — In March of last year, I published this article claiming that the latest (at the time) DD-WRT builds based on the Linux 2.6 kernel (K2.6) ran faster on a Linksys/Cisco E4200 router than their K3.x counterparts. Since then, I’ve heard apocryphal stories from some in the DD-WRT forums that the […]

DD-WRT K2.6 vs K3.x vs Tomato Router Firmware Head to ...

This entry was posted in Linux Technology and tagged DD-WRT ddwrt EdgeRouter K2.6 K2.6 vs K3.x K3 K3.x Linux networking speed speed test speedtest Tomato UBNT USG which is faster on January 7, 2017 by Steve Jenkins (updated 2875 days ago)

Cisco/Linksys E4200 overclocked to 532 MHz — UPDATE: Newer versions of the DD-WRT firmware now include a web-based option for selecting your overclock speed, if it’s supported on your device. You can still follow these steps to overclock (and I recommend you continue reading so you understand what you’re doing), but now you can access overlocking on the Administration/Management tab. […]

How To: Overclock a Cisco/Linksys E4200 Router running DD-WRT

This entry was posted in DIY Linux Reference Technology and tagged 532 MHz clock speed DD-WRT E4200 Linksys overclock overclocking on March 26, 2013 by Steve Jenkins (updated 3543 days ago)

WiFi connection on iPhone 4 — UPDATED Dec 21, 2016. This post is a reference post for those looking to squeeze maximum speed out of their Cisco Linksys E4200 v1 wireless router running DD-WRT. The DD-WRT build I currently recommend for this router is K2.6 30880 (by BrainSlayer). IMPORTANT: My testing shows that DD-WRT K2.6 builds are much faster on the […]

My Cisco Linksys E4200 DD-WRT Settings for Max Speed

This entry was posted in DIY iPhone Linux Reference Technology and tagged 22000M big BrainSlayer configuration DD-WRT ddwrt E4200 fiber Fractal Heartbleed Kong Linksys mega nas OpenSSL OpenVPN optimize settings speed std TCP Congestion Control Transmit Power usb WiFi WiFi speed wireless wireless speed on January 10, 2013 by Steve Jenkins (updated 2892 days ago)

UPDATE: I repeated my testing in January 2017, and published the results here. The older K2.6 (Linux Kernel 2.6) versions of the DD-WRT open source firmware are still way faster for both wired and wireless networks than the newer K3.x versions of DD-WRT… at least on a Linksys E4200. How can I […]

DD-WRT K2.6 is Still Faster than K3.x

This entry was posted in Linux Reference Technology on March 25, 2016 by Steve Jenkins (updated 2875 days ago)

Setting up multiple WLANs in DD-WRT — For the past while, I’ve recommended DD-WRT K2.6 firmware builds for the Linksys E4200 router, as well as other Linksys / Cisco WiFi routers. The builds based on the newer K3.x Linux kernel have now reached a stable enough point where you can run them… but I still recommend the […]

DD-WRT K2.6 Kernel vs. K3.x and How To Upgrade

This entry was posted in Linux Technology and tagged 30-30-30 DD-WRT K2.6 K2.6 vs K3.x K3 K3.x kernel reset router Upgrade WiFi WiFi router on November 20, 2015 by Steve Jenkins (updated 3163 days ago)

The Ubiquiti EdgeRouter Lite can replace the Google Fiber Network Box — I’ve been a Google Fiber user (and fan) since the service first hit Provo, Utah. I have a vacation home there, so while I don’t get to benefit from the Gigabit speeds on a daily basis, I certainly take advantage of it while I’m there. Because it’s a vacation home, I rely […]

Replace Your Google Fiber Network Box with a Ubiquiti EdgeRouter ...

This entry was posted in Linux Reference Technology and tagged config.boot EdgeMax EdgeOS EdgeRouter EdgeRouter Lite EdgeRouter POE EdgeRouter X ER-LITE ER-POE ER-X ERL ERLITE-3 GFNB Google Fiber Google Fiber Network Box Google Fiber Network Jack POE replace replace Google Fiber Network Box Ubiquiti UBNT on November 8, 2015 by Steve Jenkins (updated 2779 days ago)

Ubiquiti UAP-PRO access point — Getting decent WiFi coverage at my house has always been a challenge. The house is three stories (the bottom floor is a daylight basement) and has a footprint of 50′ x 100′. A four car garage extends the footprint even farther to the south, and because I use WiFi-controller irrigation […]

How to Install a Ubiquiti UniFi Access Point Pro (UAP-PRO)

This entry was posted in DIY Reference Technology and tagged antenna bad wifi DD-WRT how to install UAP install UAP router UAP UAP-PRO Ubiquiti UBNT WiFi on September 30, 2015 by Steve Jenkins (updated 3340 days ago)

Linksys WRT54G — I said “goodbye” to a couple of good friends today when I asked them to step down and retire after years of stellar performance. These two old friends were the last remaining Linksys WRT54G routers in use on any of my networks. I replaced them today, and in doing so, […]

Saying Goodbye To An Old Friend: Linksys WRT54G

This entry was posted in Uncategorized and tagged Belkin DD-WRT firmware flash Linksys router Tomato Ubiquiti UBNT ugprade WRT54G WRT54GL on September 27, 2015 by Steve Jenkins

Cisco/Linksys E4200 overclocked to 532 MHz — For the past few years, I’ve maintained an article on this blog offers my recommendation for the best DD-WRT build and settings to get max speed from a Linksys E4200 router. One of my recommendations in that article is to use the Administration: Commands tab in the DD-WRT GUI interface to […]

DD-WRT Speed Tweaks: Do they Really Work?

This entry was posted in Linux Technology and tagged DD-WRT Linksys router settings speed speed test tweaks on April 18, 2015 by Steve Jenkins (updated 3505 days ago)

For a few years now, I’ve been using a Linksys E4200 v1 router (running DD-WRT) as the main router at my house. However, because the WiFi signal from the router isn’t strong enough to reliably reach all the rooms in the house, I picked up a few inexpensive Belkin F7D3302 / F7D7302 […]

Adding Heat Sinks and Overclocking a Belkin F7D3302 / F7D7302 ...

This entry was posted in DIY Linux Technology and tagged Belkin cooling DD-WRT heat sink mod modding overclock router on March 24, 2015 by Steve Jenkins (updated 3529 days ago)

Cisco/Linksys E4200 overclocked to 532 MHz — It’s a question asked in the DD-WRT forums all the time. It’s a question often asked in the comments of my DD-WRT posts. And it’s a question to which no “official” answer from the primary maintainers of DD-WRT exists… and therefore it will probably keep getting asked. However, based on […]

Difference between DD-WRT BrainSlayer, Eko, Fractal, and Kong Builds

This entry was posted in Linux Technology and tagged BrainSlayer build builds DD-WRT difference Eko Fractal Kong router database SP1 SP2 version on August 21, 2013 by Steve Jenkins (updated 3661 days ago)

In an effort to extend my WiFi coverage outside our vacation home on a lake, I purchased a Ubiquiti NanoStation LOCO M5. My goal was to provide a strong WiFi signal a few hundred feet into the back yard, onto the beach, and all the way out to the dock. […]

Connecting iOS devices (iPhone, iPad, iPod) to Ubiquiti NanoStation M5 ...

This entry was posted in iPhone Linux Reference Technology and tagged 20MHz 5Ghz Apple channel channel width compatible configuration DFS frequency iOS iPad iPhone iPod LOCO NanoStation NanoStation M5 NSM5 settings troubleshoot Uqibuiti WiFi on July 15, 2013 by Steve Jenkins (updated 3437 days ago)